Exam Code: 400-101 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: CCIE Routing and Switching (v5.0)
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass 400-101 Exam.

2017 Mar 400-101 question

Q11. Which two message types allow PIM snooping to forward multicast traffic? (Choose two.) 

A. hello messages 

B. leave messages 

C. membership query messages 

D. bidirectional PIM DF election messages 

Answer: A,D 


Q12. DRAG DROP 

Drag and drop the QoS requirement on the left to the correct QoS technology on the right. 

Answer: 


Q13. Which two statements about the assert process in LAN-based PIM are true? (Choose two.) 

A. If the metrics are the same, the router with the lowest advertised routing protocol metric for that route is elected. 

B. If the metrics are the same, the router with the highest IP address on the LAN is elected. 

C. If the metrics are the same, the router with the highest advertised routing protocol metric for that route is elected. 

D. If the metrics are the same, the router with the lowest IP address on the LAN is elected. 

Answer: A,B 


Q14. Refer to the exhibit. 

Which two options are effects of the given configuration? (Choose two.) 

A. It sets the data export destination to 209.165.200.227 on UDP port 49152. 

B. It enables Cisco Express Forwarding on interface FastEthernet0/0. 

C. It configures the export process to include the BGP peer AS of the router gathering the data. 

D. It enables NetFlow switching on interface FastEthernet0/0. 

E. It sets the data export destination to 209.165.200.227 on TCP port 49152. 

Answer: A,D 

Explanation: 

The “ip flow-export destination 209.165.200.227 49152” command specifies that the data export destination server is 209.165.200.227 using UDP port 49152. 

The “ip route-cache flow” command under the fastethernet 0/0 interface enable netflow switching on that interface. 


Q15. Refer to the exhibit. 

Which two conditions can cause this error message to be displayed on the console? (Choose two.) 

A. The EtherChannel is configured as desirable on both ends. 

B. The port-channel on the adjacent device is misconfigured. 

C. There is a speed and duplex mismatch on interface fa0/12. 

D. The EtherChannel is configured as auto on one of the interfaces. 

Answer: B,C 


Far out 400-101 practice exam:

Q16. Which statement about NAT64 is true? 

A. NAT64 provides address family translation and translates IPv4 to IPv6 and IPv6 to IPv4. 

B. NAT64 provides address family translation and can translate only IPv6 to IPv4. 

C. NAT64 should be considered as a permanent solution. 

D. NAT64 requires the use of DNS64. 

Answer:


Q17. DRAG DROP 

What is the correct order of the VSS initialization process? Drag the actions on the left to the correct initialization step on the right. 

Answer: 


Q18. Which option describes a limitation of Embedded Packet Capture? 

A. It can capture data only on physical interfaces and subinterfaces. 

B. It can store only packet data. 

C. It can capture multicast packets only on ingress. 

D. It can capture multicast packets only on egress. 

Answer:

Explanation: 

Restrictions for Embedded Packet Capture 

. In Cisco IOS Release 12.2(33)SRE, EPC is supported only on 7200 platform. 

. EPC only captures multicast packets on ingress and does not capture the replicated packets on egress. 

. Currently, the capture file can only be exported off the device; for example, TFTP or FTP servers and local disk. 

Reference: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/epc/configuration/15-mt/epc-15-mt-book/nm-packet-capture.html 


Q19. Which two methods can you use to limit the range for EIGRP queries? (Choose two.) 

A. Use an access list to deny the multicast address 224.0.0.1 outbound from select EIGRP neighbor and permit everything else. 

B. Configure route tagging for all EIGRP routes. 

C. Summarize routes at the boundary routers of the EIGRP domain. 

D. Configure unicast EIGRP on all routers in the EIGRP domain. 

E. Configure stub routers in the EIGRP domain. 

F. Use an access list to deny the multicast address 224.0.0.10 outbound from select EIGRP neighbors and permit everything else. 

Answer: C,E 


Q20. External EIGRP route exchange on routers R1 and R2 was failing because the routers had duplicate router IDs. You changed the eigrp router-id command on R1, but the problem persists. Which additional action must you take to enable the routers to exchange routes? 

A. Change the corresponding loopback address. 

B. Change the router ID on R2. 

C. Reset the EIGRP neighbor relationship. 

D. Clear the EIGRP process. 

Answer: