Testking 300-360 Questions are updated and all 300-360 answers are verified by experts. Once you have completely prepared with our 300-360 exam prep kits you will be ready for the real 300-360 exam without a problem. We have Leading Cisco 300-360 dumps study guide. PASSED 300-360 First attempt! Here What I Did.

Q31. An engineer is assigned to replace an older data-grade autonomous wireless network with a Cisco controllerbased wireless network to meet Voice over WLAN needs. The customer also wants all existing cable infrastructure to be reused and no new cable be specified. How should the engineer respond to the customer’s requirements?

A. Implement the wireless network with the restraints and decrease the TPC neighbor threshold to increase Txpower to provide overlapping cell coverage at sufficient SNR to provide for Voice over WLAN service.

B. Implement the wireless network with the restraints and utilize high-gain antenna to provide overlapping cellcoverage at sufficient SNR to provide for Voice over WLAN service.

C. Inform the customer that the network will not likely function as desired and a post install survey with thepossibility of some new cable would be recommended.

D. Inform the customer that it is not possible to provide coverage and quality for Voice over WLAN usingexisting AP locations and an entire overbuild will be necessary.

Answer: C


Q32. A customer has restricted the AP and antenna combinations for a design to be limited to one model integrated antenna AP for carpeted spaces and one model external antenna AP, with high gain antennas for industrial, maintenance, or storage areas. When moving between a carpeted area to an industrial area, the engineer forgets to change survey devices and surveys several APs. Which option is the best to reduce the negative impact of the design?

A. Deploy the specified access points per area type.

B. Resurvey and adjust the design.

C. Increase the Tx power on incorrectly surveyed access points.

D. Deploy unsurveyed access points to the design.

Answer: B


Q33. A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)

A. Use APs with external antennas.

B. Use DoS attack on APs while measuring the throughput.

C. Use APs with built-in antennas.

D. Use a battery pack to power APs.

E. Use a drawing of the office space to draw AP and client placements.

F. Use APs with directional antennas.

Answer: C,D,E


Q34. A downstream packet that contains a DSCP value arrives at the WLC Ethernet interface from the wired source network. The WLC is configured for QoS WLAN 802.1p mapping. How does the WLC treat the CAPWAP QoS marking when leaving the controller interface for the respective AP and final wireless client destination?

A. No outer CAPWAP or inner QoS tagging is applied.

B. The outer CAPWAP CoS is marked and capped and the inner DSCP maintains the original marking.

C. No outer CAPWAP QoS tag is applied, but the original DSCP is maintained inside CAPWAP.

D. The outer CAPWAP DHCP is marked and capped without any inner DSCP value.

Answer: B


Q35. As part of a wireless site survey in a hospital, an engineer needs to identify potential Layer 1 interferers. In which three areas is the engineer most likely expect to find sources of 2.4 GHz and 5 GHz RF noise? (Choose three.)

A. emergency room

B. magnetic resonance imaging

C. laboratory

D. X-ray radiography

E. Gamma Knife radiation treatment

F. kitchen

Answer: A,C,F


Q36. An engineer is installing a wireless network in an industrial area with extreme temperatures and a significant amount of dust. Which enclosure should be used to protect the APs?

A. ACU

B. ADU

C. NEMA

D. WLSE

Answer: C

Explanation:

Sometimes access points (APs) are located in areas where they are subject to extreme moisture, temperatures, dust and particles. These APs might need to be mounted inside a sealed enclosure. The NEMA has a rating system for these enclosures, which are generally called NEMA enclosures.

Reference: http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/68666-wireless-sitesurvey-faq.html