It is more faster and easier to pass the Cisco cisco 300 320 exam by using Printable Cisco ARCH Designing Cisco Network Service Architectures questuins and answers. Immediate access to the Rebirth 300 320 arch pdf Exam and find the same core area 300 320 dumps questions with professionally verified answers, then PASS your exam with a high score now.

P.S. Printable 300-320 class are available on Google Drive, GET MORE: https://drive.google.com/open?id=1m2hy4cRc4wvEGEt6al4pag1GuO4GSG6M


New Cisco 300-320 Exam Dumps Collection (Question 16 - Question 24)

Q1. Which statement about NIC teaming configurations is true?

A. With ALB, all ports use one IP address and multiple MAC addresses.

B. With AFT, two NICs connect to the different switches.

C. With SFT, all ports are active.

D. With AFT, all ports use one IP address and multiple MAC addresses.

Answer: A

Explanation:

u2022 Adapter fault tolerance (AFT): With AFT designs, two NICs connect to the same switch. One adapter is active and the other standby, and they use one common IP address and MAC address.

u2022 Switch fault tolerance (SFT): With SFT designs, one port is active and the other standby, and they use one common IP address and MAC address.

u2022 Adaptive load balancing (ALB): With ALB designs, one port receives and all ports transmit using one IP

address and multiple MAC addresses.


Q2. Which of the following features might be used by the Enterprise Campus network designer as a means of route filtering?

A. IPv4 static routes

B. Route tagging using a route map in an ACL

C. Tagging routes using the BGP MED

D. EIGRP stub networks

Answer: D


Q3. Which two statements are correct regarding Flex Links? (Choose two.)

A. An interface can belong to multiple Flex Links

B. Flex Links operate only over single pairs of links.

C. Flex Link pairs must be of the same interface type.

D. Flex Links automatically disable STP so no BPDUs are propagated.

E. Failover from active to standby on Flex Links takes less than a second.

Answer: B,D

Explanation: https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/12- 2SX/configuration/guide/book/flexlink.html

"Flex Links are a pair of a Layer 2 interfaces (ports or port channels), where one interface is configured to

act as a backup to the other. Flex Links are typically configured in service-provider or enterprise networks

where customers do not want to run STP. Flex Links provide link-level redundancy that is an alternative to

Spanning Tree Protocol (STP). STP is automatically disabled on Flex Links interfaces." "A backup link does not have to be the same type as the active link"


Q4. What is the latest Cisco high-availability solution?

A. VRRP

B. HSRP

C. VSS

D. GLBP

Answer: C


Q5. Which three options are basic technical metrics that a good SLA includes? (Choose three.)

A. packet loss

B. devices

C. latency

D. clients

E. IP availability

F. distance

Answer: A,C,E


Q6. Which statement about Fibre Channel communications is correct?

A. N_Port to N_Port connections use logical node connection points.

B. Flow control is only provided by QoS.

C. It must be implemented in an arbitrated loop.

D. Communication methods are similar to those of an Ethernet bus.

Answer: A

Explanation:

Fibre Channel supports a logical node connection point between node ports (N_ports). This is similar to TCP and UDP sockets.


Q7. Which configuration represents resiliency at the hardware and software layers?

A. multiple connections and FHRP

B. HSRP and GLBP

C. redundant supervisor and power supplies

D. dual uplinks and switches

Answer: A

Explanation:

Well, redundant supervisor could also be seen as resiliency at the hard & software (cause the control plane is taken over by the second sup if there is a failure on the first one)... Again, those answers can be debated.


Q8. Which protocol should be run on the LAN side of two edge routers (that are terminating primary and backup WAN circuits) to provide quick failover in case of primary WAN circuit failure?

A. VTP

B. STP

C. VRRP

D. RIP

Answer: C


Q9. A network engineer must perform posture assessments on Cisco ASA remote access VPN clients and control their network access based on the results. What mode is the Cisco best practice NAC deployment design for this situation?

A. Layer 2 in-band real IP gateway mode

B. Layer 2 out-of-band real IP gateway mode

C. Layer 3 in-band virtual gateway mode

D. Layer 3 out-of-band virtual gateway mode

Answer: C


Recommend!! Get the Printable 300-320 dumps in VCE and PDF From Allfreedumps, Welcome to download: https://www.allfreedumps.com/300-320-dumps.html (New 482 Q&As Version)