Pass4sure offers free demo for 300 101 route exam. "ROUTE Implementing Cisco IP Routing", also known as route 300 101 exam, is a Cisco Certification. This set of posts, Passing the Cisco ccnp route 300 101 dumps exam, will help you answer those questions. The ccnp route 300 101 dumps Questions & Answers covers all the knowledge points of the real exam. 100% real Cisco ccnp routing and switching route 300 101 exams and revised by experts!

P.S. Verified 300-101 torrent are available on Google Drive, GET MORE: https://drive.google.com/open?id=1g3xBE0KhVLL-l1SXbBZMbJhQ4SK2THNQ


New Cisco 300-101 Exam Dumps Collection (Question 5 - Question 14)

New Questions 5

CORRECT TEXTROUTE.com is a small IT corporation that has an existing enterprise network that is running IPv6 0SPFv3. Currently OSPF is configured on all routers. However, R4's loopback address (FEC0:4:4) cannot be seen in R1's IPv6 routing table. You are tasked with identifying the cause of this fault and implementing the needed corrective actions that uses OPSF features and does not change the current area assignments. You will know that you have corrected the fault when R4's loopback address (FEC0:4:4) can be seen in RTs IPv6 routing table.

Special Note: To gain the maximum number of points you must remove all incorrect or unneeded configuration statements related to this issue.

Answer:

Here is the solution below:

Explanation:

To troubleshoot the problem, first issue the show running-config on all of 4 routers. Pay more attention to the outputs of routers R2 and R3 The output of the "show running-config" command of R2:

The output of the "show running-config" command of R3:

We knew that all areas in an Open Shortest Path First (OSPF) autonomous system must be physically connected to the backbone area (Area 0). In some cases, where this is not possible, we can use a virtual link to connect to the backbone through a non-backbone area. The area through which you configure the virtual link is known as a transit area. In this case, the area 11 will become the transit area. Therefore, routers R2 and R3 must be configured with the area <area id> virtual-link <neighbor router-id>command. + Configure virtual link on R2 (from the first output above, we learned that the OSPF process ID of R2 is 1):

R2>enable R2#configure terminal

R2(config)#ipv6 router ospf 1

R2(config-rtr)#area 11 virtual-link 3.3.3.3 Save the configuration:

R2(config-rtr)#end

R2#copy running-config startup-config

(Notice that we have to use neighbor router-id 3.3.3.3, not R2's router-id 2.2.2.2) + Configure virtual link on R3 (from the second output above, we learned that the OSPF process ID of R3 is 1 and we have to disable the wrong configuration of "area 54 virtual-link 4.4.4.4"):

R3>enable R3#configure terminal

R3(config)#ipv6 router ospf 1

R3(config-rtr)#no area 54 virtual-link 4.4.4.4

R3(config-rtr)#area 11 virtual-link 2.2.2.2 Save the configuration:

R3(config-rtr)#end

R3#copy running-config startup-config

You should check the configuration of R4, too. Make sure to remove the incorrect configuration statements to get the full points.

R4(config)#ipv6 router ospf 1

R4(config-router)#no area 54 virtual-link 3.3.3.3 R4(config-router)#end

After finishing the configuration doesnu2019t forget to ping between R1 and R4 to make sure they work.

Note. If you want to check the routing information, use the show ipv6 route command, not "show ip route".



New Questions 6

Which two configurations can a PPPoE client support? (Choose Two)

A. Eight clients are configured on a single CPE.

B. The client is connected to multiple hosts over DMVPN

C. The client is installed on the same network device as the server.

D. The client is connecting over an ATM PVC

E. The client is installed on a native IPv6 network.

Answer: C,D



New Questions 7

Scenario:

You have been asked to evaluate an OSPF network setup in a test lab and to answer questions a customer has about its operation. The customer has disabled your access to the show running-config command.

Which of the following statements is true about the serial links that terminate in R3

A. The R1-R3 link needs the neighbor command for the adjacency to stay up

B. The R2-R3 link OSPF timer values are 30, 120, 120

C. The R1-R3 link OSPF timer values should be 10,40,40

D. R3 is responsible for flooding LSUs to all the routers on the network.

Answer: B



New Questions 8

Which keyword of the aaa authentication ppp command supports PAP only?

A. line

B. krb5

C. local

D. local-case

E. enable

Answer: B



New Questions 9

What is the benefit of deploying IPv6 in a campus network using dual stack mode?

A. Dual Stack Mode takes advantage of IPv6 over IPv4 tunnel within a network.

B. IPv4 and IPv6 run alongside one another and have no dependency on each other to function

C. IPv4 and IPv6 share network resources.

D. IPv6 can depend on existing IPv4 routing, QoS, security, and multicast policies.

Answer: B

Explanation:

Deploying IPv6 in the campus using the dual-stack model offers several advantages over the hybrid and service block models. The primary advantage of a dual stack model is that it does not require tunneling within the campus network. The dual stack model runs the two protocols as ships in the night, meaning that IPv4 and IPv6 run alongside one another and have no dependency on each other to function except that they share network resources. Both have independent routing.



New Questions 10

Which statement about the use of tunneling to migrate to IPv6 is true?

A. Tunneling is less secure than dual stack or translation.

B. Tunneling is more difficult to configure than dual stack or translation.

C. Tunneling does not enable users of the new protocol to communicate with users of the old protocol without dual-stack hosts.

D. Tunneling destinations are manually determined by the IPv4 address in the low-order 32 bits of IPv4-compatible IPv6 addresses.

Answer: C



New Questions 11

A network engineer is modifying RIPng timer configuration. Which configuration mode should the engineer use?

A. router(config-rtr)#

B. router(config-ripng)#

C. router(config-if)#

D. router(config)#

Answer: C

Explanation:

http://www.cisco.com/c/en/us/td/docs/ios/12_2/ip/configuration/guide/fipr_c/1cfrip.html



New Questions 12

Which two statements about password-protecting device access are true (choose two)

A. The more system:running-config command displays encrypted passwords in clear text

B. The service password-encryption command forces a remote device to encrypt the password

C. A network administrator can recover an encrypted password

D. The privilege level command controls the commands a specific user can execute

E. The password can be encrypted in the running configuration

Answer: D,E



New Questions 13

Refer to the exhibit. Will redistributed RIP routes from OSPF Area 2 be allowed in Area 1?

A. Because Area 1 is an NSSA, redistributed RIP routes will not be allowed.

B. Redistributed RIP routes will be allowed in Area 1 because they will be changed into type 5 LSAs in Area 0 and passed on into Area 1.

C. Because NSSA will discard type 7 LSAs, redistributed RIP routes will not be allowed in Area 1.

D. Redistributed RIP routes will be allowed in Area 1 because they will be changed into type 7 LSAs in Area 0 and passed on into Area 1.

E. RIP routes will be allowed in Area 1 only if they are first redistributed into EIGRP.

Answer: A

Explanation:

The following are several area types that are possible on OSPF:



New Questions 14

Which two statements about Frame Relay Point-to-Point connections are true? (Choose Two)

A. Changing a point-to-point sub interface to a different type requires the device to be reloaded.

B. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud.

C. The device can establish a point-to-point connection to the cloud without a DLCI.

D. They can operate normally without a DLCI map.

E. Each physical interface that extends to the Frame Relay cloud can support a single SVC.

Answer: A,B



P.S. Easily pass 300-101 Exam with Examcollectionplus Verified Dumps & pdf vce, Try Free: https://www.examcollectionplus.net/vce-300-101/ (487 New Questions)