Proper study guides for Renew Cisco Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) certified begins with Cisco 300 075 vce preparation products which designed to deliver the Precise 300 075 vce questions by making you pass the 300 075 pdf test at your first time. Try the free 300 075 vce demo right now.

Q41. Refer to the exhibit. 

The HQ site uses area code 650. The BR1 site uses area code 408. The long distance national code for PSTN dialing is 1. To make a long distance national call, an HQ or BR1 user dials access code 9, followed by 1, and then the 10-digit number. Both sites use MGCP gateways. AAR must use globalized call routing using a single route pattern. Assume that all outgoing PSTN numbers are localized at the egress gateway as shown in the exhibit. Which statement is true? 

A. The AAR group system must be configured on the device configuration of the phones. 

B. The AAR group system must be configured on the line configuration of the phones. 

C. The single AAR group system cannot be used. A second AAR group must be configured in order to have source and destination AAR groups. 

D. The AAR group system must be configured under the AAR service parameters. 

Answer:


Q42. Which two options are requirements for deploying an H.323 gateway with Cisco Unified Communications Manager? (Choose two.) 

A. Cisco Unified Communications Manager and the H.323 gateway must be configured use the same TCP port for H.323 calls. 

B. The H.245TCSTimeout timer must be set to at least 25. 

C. Cisco voicemail ports must be active. 

D. The Media Exchange Interface Capability Timer must be set to less than 20. 

E. The Media Exchange Timer must be set to less than 20. 

Answer: A,B 


Q43. When an external call is placed from Ajax, they would like the ANI that is sent to the PSTN to be the main number, not the extension. For domestic calls, they would like 10 digits sent; for international calls, they would like to send the country code 1 and the 10 digits. How can this be accomplished? 

A. Add a translation pattern to the dial peers in the gateway that adds the appropriate digits to the outgoing ANI. 

B. In the external call route patterns, set the external phone number mask to the main number. Use 10 digits in the domestic route pattern and 1 followed by the main number digits in the international route patterns. 

C. Use a calling party transform mask for each route group in the corresponding route list configuration. Set the explicit 10-digit main number for domestic calls and 1 followed by the main number for the international route patterns. 

D. In the directory number configurations, set the prefix digits field to the country code and the 10 digits of the main number. This will be truncated to the 10-digit number for domestic calls and sent out in its entirety for international calls. 

Answer:

Explanation: 

Incorrect Answer: A, B, D calling party transformation mask value is Valid entries for the NANP include the digits 0 through 9; the wildcard characters X, asterisk (*), and octothorpe (#); and the international escape character +. Link: 

http://www.cisco.com/en/US/docs/voice_ip_comm/cucmbe/admin/8_6_1/ccmcfg/b03trpat.ht ml 


Q44. Refer to the exhibit: 

The exhibit shows a SAF Forwarder configuration attached to a Cisco Unified Communications Manager. 

Which minimum configuration for a Cisco Unified Communications Manager Express SAF Forwarder is needed to establish a SAF neighbor relationship with this SAF Forwarder? 

A. router eigrp SAFiservice-family ipv4 autonomous-system 1!topology baseexit-sf-topologyexit-service-familyvoice service safprofile trunkroute 1session protocol sip interface Loopback1 transport tcp port 5060! 

B. router eigrp SAF!service-family ipv4 autonomous-system 1!topology baseexit-sf-topologyexit- service-family!voice service safprofile trunk-route 1session protocol sip interface Loopback1 transport tcp port 5060!profile dn-block 1 alias-prefix 1972555pattern 1 type extension 4xxx!profile callcontrol 1dn-servicetrunk-route 1dn-block 1dn-block 2!channel 1 vrouter SAF asystem 1subscribe callcontrol wildcardedpublish callcontrol 1! 

C. router eigrp SAF!service-family ipv4 autonomous-system 1!topology baseexit-sf-topologyexit-service-family! 

D. None of above configurations contain sufficient information. 

Answer:

Explanation: 

Incorrect Answer: A, B, D only following configuration is enough router eigrp SAF service-family ipv4 autonomous-system 1 exit-service-family link: 

http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6554/ps6599/ps10822/whitepaper_c11-636604.html 


Q45. Which configuration command disables the secondary dial tone on the branch office ISR for users calling from the PSTN into the branch office during a WAN failure? 

A. direct-inward-dial 

B. voice translation-rule 

C. incoming called-number 

D. application 

Answer:


Q46. Scenario 

There are two call control systems in this item. The Cisco UCM is controlling the DX650, the Cisco Jabber for Windows Client, and the 7965 and 9971 Video IP Phones. The Cisco VCS and TMS control the Cisco TelePresence Conductor, the Cisco TelePresence MCU, and the Cisco Jabber TelePresence for Windows. 

Use the exhibits to answer the following questions. 

DNS Servers 

Device Pool 

Expressway 

ILS 

Locations 

MRA 

Speed Dial 

SIP Trunk 

Which three configuration tasks need to be completed on the router to support the registration of Cisco Jabber clients? (Choose three.) 

A. The DNS server has the wrong IP address. 

B. The internal DNS Service (SRV) records need to be updated on the DNS Server. 

C. Flush the DNS Cache on the client. 

D. The DNS AOR records are wrong. 

E. Add the appropriate DNS SRV for the Internet entries on the DNS Server. 

Answer: B,C,E 


Q47. What is the difference between an MGCP gateway and a SIP gateway? 

A. An MGCP gateway that dial peers be configured before PSTN calls can be placed and received. The SIP gateway requires no dial peers. 

B. An MGCP gateway can be added in Cisco Unified Communications Manager under the Gateway Type field using the gateway model. The SIP gateway can connect to Cisco Unified Communications Manager only through a SIP trunk. 

C. A SIP gateway requires a call agent for PSTN calls to be placed and received. An MGCP gateway does not require a call agent for PSTN calls to be placed and received. 

D. An MGCP gateway can register with Cisco Unified Communications Manager. A SIP gateway will show status of "Unknown". 

E. The SIP gateway must be configured in Cisco Unified Communications Manager using a valid IP address on the gateway. The MGCP gateway must be configured in Cisco Unified 

Communications Manager using the domain name. 

Answer:


Q48. Refer to the exhibit. 

The HQ site uses area code 650. The BR1 site uses area code 408. The long distance national code for PSTN dialing is 1. To make a long distance national call, an HQ or BR1 user dials access code 9, followed by 1, and then the 10-digit number. 

Both sites use MGCP gateways. AAR must use globalized call routing using a single route pattern. Assume that all outgoing PSTN numbers are localized at the egress gateway as shown in the exhibit. 

Which partition should be configured in the AAR CSS applied at the phones? 

A. PSTN partition 

B. LD partition 

C. The HQ AAR CSS must include a partition assigned to route pattern 91408XXXXXXX. The BR1 AAR CSS must include a partition assigned to route pattern 91650XXXXXXX. 

D. AAR CSS must contain translation pattern 9.1[2-9]XX[2-9]XXXXXX for each site that must be globalized. Otherwise the called numbers will not be localized at the egress gateway. 

Answer:


Q49. Refer to the exhibit. 

The H.323 Gateway is showing status “unknown”. Which statement is true? 

A. The gateway must be reset in Cisco Unified Communications Manager. 

B. The no gateway command followed by the gateway command must be issued in Cisco IOS. 

C. The mgcp commands must be removed. 

D. H.323 gateways do not register with Cisco Unified Communications Manager H.323 gateways always show status "Unknown". 

E. VUAN 1 20 may be down and so the H.323 gateway appears offline to the Cisco Unified Communications Manager 

Answer:

Explanation: 

Incorrect Answer: A, B, C, E 

After a gateway is registered with Cisco Unified Communications Manager, gateway registration status may display in Cisco Unified Communications Manager Administration as unknown. 

Link: 

http://www.cisco.com/en/US/docs/voice_ip_comm/cucmbe/admin/8_6_1/ccmcfg/b06gtway. html 


Q50. What command is used to map internal extensions to the corresponding E.164 PSTN number when using Cisco Unified Communications Manager Express in SRST mode? 

A. ephone-dn 

B. dialplan-pattern 

C. number 

D. number-e.164 

E. ephone-transnumber 

Answer: