It is impossible to pass Cisco cisco 300 070 exam without any help in the short term. Come to Testking soon and find the most advanced, correct and guaranteed Cisco 300 070 ciptv1 practice questions. You will get a surprising result by our Up to the immediate present Implementing Cisco IP Telephony & Video, Part 1 v1.0 practice guides.

Q11. Which two features are advantages of deploying a cluster over WAN? (Choose two.) 

A. Shared line appearances 

B. CentralizedDSP resources 

C. Extension mobility within the cluster 

D. Scalability up to 20 sites, if thereis sufficient IP WAN bandwidth 

E. Failover to co-resident Cisco UnifiedCall Manager Express platforms 

Answer: A,C 

Q12. Which two types of encoding are available to configure a T1 controller for CAS? 

A. AME. 

B. ESF. 

C. SF. 

D. B8SF. 

E. B8ZS. 

F. AMI. 

Answer: E,F 

Explanation: Reference: 

Q13. Which three Cisco Unified CallManager configuration steps are required to support third party SIPphones? (Choose three.) 

A. Configure the device in Cisco Unified CallManager. 

B. Change the proxy address in the SIP phone to an IP address or the Fully Qualified Domain Name (FQDN)of Cisco Unified CallManager. 

C. Associate the device with the end user. 

D. Configure the phone with the TLS username and password. 

E. Configure the end user in Cisco Unified CallManager. 

F. Add the MAC address of the Cisco Unified CallManager server to the SIP phone configuration page. 

Answer: A,C,E 

Q14. If the route patterns 5XXX, 51XX, 513X and 5134 exist within a call route database, which pattern would be matched if the dialed number was 5324? 

A. 5XXX 

B. 51XX 

C. 513X 

D. 5134 


Q15. When a call is attempted during a particular time of day, what determines the partitions where calling devices search? 

A. time schedules 

B. calling periods 

C. dial schedules 

D. time periods 


Q16. What is the difference between policing and shaping? 

A. Policing: Transmit and mark, then transmit the packets. Shaping: Buffer the exceeding packets. 

B. Policing: Transmit the packets. Shaping: Buffer the exceeding packets. 

C. Policing: Transmit, drop or mark, then transmit the packets. Shaping: Buffer the exceeding packets. 

D. Policing: Buffer the exceeding packets. Shaping: Transmit and mark, then transmit the packets. 


Explanation: Reference: 

Q17. Which two Cisco products allow the use of a dial plan with E.164, H.323, SIP, and DNS? (Choose two.) 

A. Cisco Expressway 

B. Cisco Unified Communications Manager 

C. Cisco Unified Border Element 

D. Cisco IM and Presence 

E. Cisco TelePresence Video Communication Server 

Answer: A,E 

Q18. After you configure a dial plan to call a particular prefix in the PSTN, you notice that some outbound calls are taking longer than usual (15 seconds) before you hear a connecting tone. What is the likely cause of this issue? 

A. The outbound gateway must be configured with the new prefix. 

B. The endpoint is choosing the best codec to use. 

C. The new prefix is overlapping other route patterns. 

D. With some prefixes, this is normal behavior of the PSTN. 


Explanation: Reference: 

Page 107 


Q19. Which mechanism is often configured on the edges of a network to control the maximum rate of traffic that is sent or received on an interface and to classify the traffic into priority levels or class of service? 

A. routing 

B. shaping 

C. policing 

D. access control 

E. traffic regulation 


Q20. Which parameter is required on MCU for ad hoc conferencing? 

A. Media Port reservation 

B. incoming calls to unknown conferences or auto-attendants 

C. DSP reservation for video 

D. MCU type 

E. MCU Conference Bridge SIP Port