Master the 2v0 620 dump vSphere 6 Foundations Beta Exam content and be ready for exam day success quickly with this Ucertify 2v0 620 dump training. We guarantee it!We make it a reality and give you real 2v0 620 dump questions in our VMware 2v0 620 exam braindumps.Latest 100% VALID VMware vmware 2v0 620 Exam Questions Dumps at below page. You can use our VMware 2v0 620 pdf braindumps and pass your exam.
Q1. An administrator has just configured the IP address on an ESXi host from the Direct Console User Interface.
How can the configuration be validated as correct without any additional tools?
A. Add the host to vCenter Server and if it works, then all networking settings are ok.
B. Select the Test Management Network option from the DCUI.
C. Connect to the host with the vSphere Client and click the Test Network option.
D. Use PowerCLI to connect to the host and initiate a network test.
Q2. When configuring vSphere Replication for a virtual machine, what is the lowest Recovery Point Objective (RPO) that can be selected?
A. 1 min
B. 5 min
C. 10 min
Q3. An administrator is deploying multiple Windows 2003 Virtual Machines from the same template.
What two steps should be taken to avoid network conflicts? (Choose two.)
A. Customize the guest operating system.
B. Install VMware Tools into the new virtual machines.
C. Copy the Microsoft Sysprep tools onto the vCenter Server system.
D. Ensure the e1000 vmnic is selected for each new virtual machine.
Q4. Your manager has given you a bash script that retrieves data for ESXi 6.x host configurations. This data needs to be collected right after the installation of a host and must be run directly on the host.
Which two actions can be used to run this script on an ESXi host? (Choose two.)
A. Connect to the host with Ruby vSphere Console and run the script from there.
B. Enable SSH access from the Direct Console User Interface.
C. Enable the ESXi Shell from the Direct Console User Interface.
D. Run the script directly from the vSphere Web Client.
Q5. A physical Windows 2008 R2 Server is converted to a virtual machine using VMware vCenter Converter. Upon completion of the conversion and subsequent power on operation, the virtual machine fails to boot and the message below is observed in the Console of the virtual machine:
STOP 0x0000007B INACCESSIBLE_BOOT_DEVICE
Which two potential issues may be causing this boot failure? (Choose two.)
A. An incorrect SCSI controller was selected during conversion.
B. Incompatible software drivers were migrated into the virtual machine from the source machine.
C. The vmdk file backing the virtual machine was thick provisioned.
D. A snapshot was taken immediately after the conversion completed.
Q6. Which two actions are required when enabling vFlash Read Cache for a virtual machine's virtual disk? (Choose two.)
A. A value in the Virtual Flash Read Cache text box must be entered.
B. A Flash Resource Pool for Cache size reservation must be entered.
C. The Device backing and the block size must be configured.
D. The Enable virtual flash host swap cache check box must be selected.
Q7. Which two configurable options apply to both virtual machine CPU and memory allocation? (Choose two.)
C. Resource Pool
D. Reserve All
Q8. Which three are architecture components of vRealize Operations? (Choose three.)
A. Identity Server
B. Administrative Server
C. Analytics Server
D. Database Server
E. Connection Broker
Q9. An administrator is troubleshooting basic network connectivity issues.
Which two scenarios are potential issues that this administrator might face? (Choose two.)
A. The vSwitch is not attached to the correct physical network.
B. The portgroup is not configured to use correct VLAN.
C. Traffic shaping is configured incorrectly.
D. Jumbo frames is configured incorrectly.
Q10. Which two NFS Protocol versions does vSphere 6 support? (Choose two.)
A. Version 3
B. Version 3.1
C. Version 4
D. Version 4.1