Q21. Refer to the exhibit. 

Which configuration element can be used to specify the Multiway address that can be used by the endpoint to initiate Multiway calls? 

A. Conference 1 

B. NetworkServices 

C. Provisioning 

D. SIP Profile 1 

E. Video 

Answer:


Q22. Management wants to modify Cisco TMS to allow users to configure the call behavior with their associated devices and dial from a single ID. Which feature needs to be enabled and configured? 

A. Smart Scheduler 

B. Low-touch Provisioning 

C. FindMe 

D. CMR Provisioning 

Answer:


Q23. A user is currently on a Cisco TelePresence call using a Touch 8 device and would like to change the local screen layout so that the active speaker is in full screen and the other participants are smaller within the picture. Which layout option should the user choose? 

A. Prominent 

B. Overlay 

C. PiP 

D. FullScreen 

Answer:


Q24. The user of a Cisco TelePresence MX300 wants to control the far-end camera of any video conference participant. Which control device and function is used to control the far-end camera? 

A. Navigate using the TRC5 Remote Control arrow keys. 

B. Tap on the image of one of the participants using touch control. 

C. Use the Touch Control Conference functions. 

D. Use the TRC5 Remote Control home key. 

Answer:


Q25. To which Ethernet port on a Cisco TelePresence System (500/1x00/1300/3xx0) endpoint would a technician need to connect to manually assign a static IP address for first-time setup? 

A. IP phone port 

B. network port 

C. camera port 

D. auxiliary network port 

Answer:


Q26. An engineer is configuring VIP mode for a Cisco TelePresence Multipoint Switch. What are three characteristics the engineer must keep in mind? (Choose three.) 

A. VIP mode can be configured only when the meeting is not active. 

B. The VIP is displayed on the center screen for three screen systems. 

C. Network multipoint meetings are supported. 

D. VIP mode timers must be configured from the CLI. 

E. Locking is not supported. 

F. Only one VIP can be configured for each meeting. 

Answer: B,D,F 


Q27. Refer to the exhibit. 

A network engineer is attempting to register a Cisco TelePresence endpoint to a Cisco VCS. What is the most likely cause of this failure? 

A. The lab.local SIP domain is not configured in the Cisco VCS allow list for registration. 

B. The Cisco VCS failed to bind to the LDAP server, which is where the lab.local SIP domain is learned. 

C. The lab.local SIP domain does not exist on the Cisco VCS. 

D. The endpoint does not have the proper port assignments configured for SIP signaling. 

E. The endpoint uses the TCP protocol and the Cisco VCS is configured to allow only TLS for SIP registrations. 

Answer:


Q28. A network engineer wants to quickly view any issues that may exist for a newly deployed Cisco TelePresence SX20 codec. To which location in the codec web GUI should the engineer navigate to find this information? 

A. Diagnostics > Alerts 

B. Diagnostics > Troubleshooting 

C. Configuration > System Status 

D. Configuration > Security 

Answer:


Q29. Refer to the exhibit. 

Which system tab can be used to add video infrastructure devices and endpoints? 

A. Navigator 

B. System Overview 

C. Configuration Templates 

D. Provisioning 

E. Administrative Tools 

Answer:


Q30. The command xCommand Security FIPSMode Activate is issued to a Cisco TelePresence C-Series codec. Management wants to reverse the effects of this command. Which two methods could be used for this purpose? (Choose two.) 

A. From the touch screen, disable FIPS mode in the Administrator Settings menu. 

B. From the touch screen, perform a factory reset from the Administrator Settings menu. 

C. From the touch screen, disable all security settings from the Administrator Settings menu. 

D. Use SSH to connect to the system and enter the xCommand Security FIPSMode Deactivate command. 

E. Use Telnet to connect to the system and enter the xCommand SystemUnit FactoryReset Init command. 

F. Use SSH to connect to the system and enter the xCommand SystemUnit FactoryReset Confirm: Yes command. 

Answer: B,F