It is impossible to pass Cisco 200-105 exam without any help in the short term. Come to Examcollection soon and find the most advanced, correct and guaranteed Cisco 200-105 practice questions. You will get a surprising result by our Refresh Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) practice guides.

2017 Mar 200-105 free question

Q21. - (Topic 2) 

A router is running three routing processes: RIP, OSPF, and EIGRP, each configured with default characteristics. Each process learns a route to the same remote network. 

If there are no static routes to the destination and none of the routes were redistributed, which route will be placed in the IP routing table? 

A. the route learned through EIGRP 

B. the route learned through OSPF 

C. the route learned through RIP 

D. the route with the lowest metric 

E. all three routes with the router load balancing 

Answer:

Reference: 

http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080094195.shtml 

Administrative distance is the feature that routers use in order to select the best path. 

Administrative distance defines the reliability of a routing protocol. Each routing protocol is prioritized in order of most to least reliable (believable) with the help of an administrative distance value. Lowest Administrative distance will be chosen first. 


Q22. - (Topic 2) 

When a router undergoes the exchange protocol within OSPF, in what order does it pass through each state? 

A. exstart state > loading state > exchange state > full state 

B. exstart state > exchange state > loading state > full state 

C. exstart state > full state > loading state > exchange state 

D. loading state > exchange state > full state > exstart state 

Answer:

Explanation: 

OSPF states for adjacency formation are (in order) Down, Init, Attempt, 2-way, Exstart, 

Exchange, Loading and Full. 

Reference: 

Why Are OSPF Neighbors Stuck in Exstart/Exchange State? 

http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080093f0d.shtml 


Q23. - (Topic 1) 

What is one benefit of PVST+? 

A. PVST+ supports Layer 3 load balancing without loops. 

B. PVST+ reduces the CPU cycles for all the switches in the network. 

C. PVST+ allows the root switch location to be optimized per VLAN. 

D. PVST+ automatically selects the root bridge location, to provide optimized bandwidth usage. 

Answer:

Explanation: 

Per VLAN Spanning Tree (PVST) Introduction http://www.cisco.com/en/US/tech/tk389/tk621/tk846/tsd_technology_support_sub-protocol_home.html Per VLAN Spanning Tree (PVST) maintains a spanning tree instance for each VLAN configured in the network. This means a switch can be the root bridge of a VLAN while another switch can be the root bridge of other VLANs in a common topology. For example, Switch 1 can be the root bridge for Voice data while Switch 2 can be the root bridge for Video data. If designed correctly, it can optimize the network traffic. http://www.ciscopress.com/articles/article.asp?p=102157&seqNum=4 

Topic 2, Routing Technologies 


Q24. - (Topic 1) 

Refer to the exhibit 

Which switch provides the spanning-tree designated port role for the network segment that services the printers? 

A. Switch1 

B. Switch2 

C. Switch3 

D. Switch4 

Answer:

Explanation: 

First, the question asks what switch services the printers, so it can be Switch 3 or Switch 4 

which is connected directly to the Printers. 

Designated port is a port that is in the forwarding state. All ports of the root bridge are 

designated ports. 

Switch 3 and Switch 4 has same priority so it will see on lowest MAC address and here 

switch 3 has lowest MAC address. So switch 3 segment will play a Designated port role. 

By comparing the MAC address of Switch 3 and Switch 4 we found that the MAC of Switch 

3 is smaller. Therefore the interface connected to the Printers of Switch 3 will become 

designated interface and the interface of Switch 4 will be blocked. 


Q25. - (Topic 2) 

Which two statements about the OSPF Router ID are true? (Choose two.) 

A. It identifies the source of a Type 1 LSA. 

B. It should be the same on all routers in an OSPF routing instance. 

C. By default, the lowest IP address on the router becomes the OSPF Router ID. 

D. The router automatically chooses the IP address of a loopback as the OSPF Router ID. 

E. It is created using the MAC Address of the loopback interface. 

Answer: A,D 

Explanation: 

From the output of the “show ip ospf database”: r120#show ip ospf data 

OSPF Router with ID (10.0.0.120) (Process ID 1) 

Next, who are the other routers in our area? Router Link States (Area 1) Link ID.ADV Router.Age.Seq#.Checksum Link count 

10.0.0.111.10.0.0.111.600.0x8000023A 0x0092B3 1 

10.0.0.112.10.0.0.112.1246.0x80000234 0x009CAC 1 

10.0.0.113.10.0.0.113.148.0x8000022C 0x004399 3 

10.0.0.120.10.0.0.120.152.0x80000240 0x0046CB 1 This tells us there are four routers in Area 1. The router with RID 10.0.0.113 has 3 links in Area 1, every one else has only 1 link. Also the router will chose the highest loopback interface as its OSPF router ID (if available). 


Renovate 200-105 test question:

Q26. DRAG DROP - (Topic 2) 

Answer: Explanation: 

poison reverse: A router learns from its neighbor that a route is down and the router sends an update back to the neighbor with an infinite metric to that routeLSA: The packets flooded when a topology change occurs, causing network routers to update their topological databases and recalculate routes split horizon: This prevents sending information about a routeback out the same interface that originally learned about the route holddown timer: For a given period, this causes the router to ignore any updates with poorer metrics to a lost network 

The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the graphic. There is concern that a lack of router resources is impeding internetwork performance. As part of examining the router resources, the OSPF DRs need to be known. All the router OSPF priorities are at the default and the router IDs are shown with each router. 

Which routers are likely to have been elected as DR? (Choose two.) 

A. Corp-1 

B. Corp-2 

C. Corp-3 

D. Corp-4 

E. Branch-1 

F. Branch-2 

Answer: D,F 

Explanation: There are 2 segments on the topology above which are separated by Corp-3 router. Each segment will have a DR so we have 2 DRs. 

To select which router will become DR they will compare their router-IDs. The router with highest (best) router-ID will become DR. The router-ID is chosen in the order below: 

The highest IP address assigned to a loopback (logical) interface. 

If a loopback interface is not defined, the highest IP address of all active router’s physical interfaces will be chosen. 

In this question, the IP addresses of loopback interfaces are not mentioned so we will consider IP addresses of all active router’s physical interfaces. Router Corp-4 (10.1.40.40) & Branch-2 (10.2.20.20) have highest “active” IP addresses so they will become DRs. 


Q27. - (Topic 1) 

Refer to the exhibit. 

Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.) 

A. SwitchA, Fa0/2, designated 

B. SwitchA, Fa0/1, root 

C. SwitchB, Gi0/2, root 

D. SwitchB, Gi0/1, designated 

E. SwitchC, Fa0/2, root 

F. SwitchD, Gi0/2, root 

Answer: A,B,F 

Explanation: 

The question says "no other configuration changes have been made" so we can 

understand these switches have the same bridge priority. SwitchC has lowest MAC 

address so, it will become root bridge and 2 of its ports (Fa0/1 & Fa0/2) will be designated 

ports (DP). Because SwitchC is the root bridge the 2 ports nearest SwitchC on SwitchA 

(Fa0/1) and SwitchD (Gi0/2) will be root ports (RP) -> B and F are correct. 

SwitchB must have a root port so which port will it choose? To answer this question we 

need to know about STP cost and port cost. 

In general, "cost" is calculated based on bandwidth of the link. The higher the bandwidth on 

a link, the lower the value of its cost. Below are the cost values you should memorize: 

Link speed Cost SwitchB will choose the interface with lower cost to the root bridge as the root port so we must calculate the cost on interface Gi0/1 & Gi0/2 of SwitchB to the root bridge. This can be calculated from the "cost to the root bridge" of each switch because a switch always advertises its cost to the root bridge in its BPDU. The receiving switch will add its local port cost value to the cost in the BPDU. SwitchC advertises its cost to the root bridge with a value of 0. Switch D adds 4 (the cost value of 1Gbps link) and advertises this value (4) to SwitchB. SwitchB adds another 4 and learns that it can reach SwitchC via Gi0/1 port with a total cost of 8. The same process happens for SwitchA and SwitchB learns that it can reach SwitchC via Gi0/2 with a total cost of 23 -> Switch B chooses Gi0/1 as its root port. Now our last task is to identify the port roles of the ports between SwitchA & SwitchB. It is rather easy as the MAC address of SwitchA is lower than that of SwitchB so Fa0/2 of SwitchA will be designated port while Gi0/2 of SwitchB will be alternative port. 


Q28. - (Topic 2) 

Which type of EIGRP route entry describes a feasible successor? 

A. a backup route, stored in the routing table 

B. a primary route, stored in the routing table 

C. a backup route, stored in the topology table 

D. a primary route, stored in the topology table 

Answer:

Explanation: 

http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080093f07.shtml 

Feasible Successors A destination entry is moved from the topology table to the routing table when there is a feasible successor. All minimum cost paths to the destination form a set. From this set, the neighbors that have an advertised metric less than the current routing table metric are considered feasible successors. Feasible successors are viewed by a router as neighbors that are downstream with respect to the destination. These neighbors and the associated metrics are placed in the forwarding table. When a neighbor changes the metric it has been advertising or a topology change occurs in the network, the set of feasible successors may have to be re-evaluated. However, this is not categorized as a route recomputation. Feasible successor is a route whose Advertised Distance (AD) is less than the Feasible Distance (FD) of the current best path. A feasible successor is a backup route, which is not stored in the routing table but, stored in the topology table. 


Q29. - (Topic 2) 

What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router? 

A. 2 

B. 4 

C. 16 

D. unlimited 

Answer:

Explanation: 

4 is the default number of routes that OSPF will include in routing table if more than 4 equal cost routes exist for the same subnet. However, OSPF can include up to 16 equal cost routes in the routing table and perform load balancing amongst them. In order to configure this feature, you need to use the OSPF subcommand maximum-paths, i.e. maximum-paths 16. 


Q30. DRAG DROP - (Topic 3) 

Answer: 

Explanation: 

1) a router is this type of device: DTE2) the most common type of virtual circuit: PVC3) provides status messages between DTE and DCE devices: LMI4) identifies the virtual connection between the DTE and the switch: DLCI 

CCNA Certification Test Prep Case Study http://www.thebryantadvantage.com/CCNACertificationExamTutorialDirectlyConnectedSeri alInterfaces.htm Configuring the LMI Type on a Frame Relay Interface http://www.ciscopress.com/articles/article.asp?p=170741&seqNum=3 Frame Relay DLCIs And Mappings http://www.mcmcse.com/cisco/guides/frame_relay_dlci.shtml