It is impossible to pass Check Point 156-915.80 exam without any help in the short term. Come to Ucertify soon and find the most advanced, correct and guaranteed Check Point 156-915.80 practice questions. You will get a surprising result by our Refresh Check Point Certified Security Expert Update - R80 practice guides.
P.S. Verified 156-915.80 questions are available on Google Drive, GET MORE: https://drive.google.com/open?id=1YYqgCO6ctCwcBVUFbQYMfHPbrQOvemUT
New Check Point 156-915.80 Exam Dumps Collection (Question 2 - Question 11)
Q1. Which packet info is ignored with Session Rate Acceleration?
A. source port ranges
B. source ip
C. source port
D. same info from Packet Acceleration is used
Q2. The third-shift Administrator was updating Security Management Server access settings in Global Properties. He managed to lock all administrators out of their accounts. How should you unlock these accounts?
A. Delete the file admin.lock in the Security Management Server directory $FWDIR/tmp/.
B. Reinstall the Security Management Server and restore using upgrade_import.
C. Type fwm lock_admin -ua from the Security Management Server command line.
D. Login to SmartDashboard as the special cpconfig_admin user account; right-click on each administrator object and select unlock.
Q3. MultiCorp is located in Atlanta. It has a branch office in Europe, Asia, and Africa. Each location has its own AD controller for local user login. How many ADqueries have to be configured?
Q4. You are about to integrate RSA SecurID users into the Check Point infrastructure. What kind of users are to be defined via SmartDashboard?
A. A group with generic user
B. All users
C. LDAP Account Unit Group
D. Internal user Group
Q5. You have three Gateways in a mesh community. Each gatewayu2019s VPN Domain is their internal network as defined on the Topology tab setting All IP Addresses behind Gateway based on Topology information.
You want to test the route-based VPN, so you created VTIs among the Gateways and created static route entries for the VTIs. However, when you test the VPN, you find out the VPN still go through the regular domain IPsec tunnels instead of the routed VTI tunnels.
What is the problem and how do you make the VPN use the VTI tunnels?
A. Domain VPN takes precedence over the route-based VTI. To make the VPN go through VTI, remove the Gateways out of the mesh community and replace with a star community
B. Domain VPN takes precedence over the route-based VTI. To make the VPN go through VTI, use an empty group object as each Gatewayu2019s VPN Domain
C. Route-based VTI takes precedence over the Domain VPN. To make the VPN go through VTI, use dynamic-routing protocol like OSPF or BGP to route the VTI address to the peer instead of static routes
D. Route-based VTI takes precedence over the Domain VPN. Troubleshoot the static route entries to insure that they are correctly pointing to the VTI gateway IP.
Q6. When restoring R80 using the command upgrade_import, which of the following items are NOT restored?
A. SIC Certificates
C. Route tables
D. Global properties
Q7. What are you required to do before running the command upgrade_export?
A. Run a cpstop on the Security Gateway.
B. Run a cpstop on the Security Management Server.
C. Close all GUI clients.
D. Run cpconfig and set yourself up as a GUI client.
Q8. When a packet is flowing through the security gateway, which one of the following is a valid inspection path?
A. Acceleration Path
B. Small Path
C. Firewall Path
D. Medium Path
Q9. You noticed that CPU cores on the Security Gateway are usually 100% utilized and many packets were dropped. You donu2019t have a budget to perform a hardware upgrade at this time. To optimize drops you decide to
use Priority Queues and fully enable Dynamic Dispatcher. How can you enable them?
A. fw cti multik dynamic_dispatching on
B. fw cti multik dynamic_dispatching set_mode 9
C. fw cti multik set_mode 9
D. fw cti multik pq enable
To fully enable the CoreXL Dynamic Dispatcher on Security Gateway:
1. Run in Expert mode:
[Expert@HostName]# fw ctl multik set_mode 9 Example output:
[Expert@R77.30:0]# fw ctl multik set_mode 9
Please reboot the system [Expert@R77.30:0]#
Q10. Fill in the blank. You can set Acceleration to ON or OFF using command syntax .
100% Refresh Check Point 156-915.80 Questions & Answers shared by Allfreedumps, Get HERE: https://www.allfreedumps.com/156-915.80-dumps.html (New Q&As)