Want to know Ucertify 156-915.80 Exam practice test features? Want to lear more about Check Point Check Point Certified Security Expert Update - R80 certification experience? Study High quality Check Point 156-915.80 answers to Latest 156-915.80 questions at Ucertify. Gat a success with an absolute guarantee to pass Check Point 156-915.80 (Check Point Certified Security Expert Update - R80) test on your first attempt.

P.S. High quality 156-915.80 training materials are available on Google Drive, GET MORE: https://drive.google.com/open?id=1kHtvfzv89_QPh4A3_cAnuAFq9mDuP3yP


New Check Point 156-915.80 Exam Dumps Collection (Question 4 - Question 13)

Q4. How could you compare the Fingerprint shown to the Fingerprint on the server? Exhibit:

A. Run cpconfig, select the Certificate's Fingerprint option and view the fingerprint

B. Run cpconfig, select the GUI Clients option and view the fingerprint

C. Run cpconfig, select the Certificate Authority option and view the fingerprint

D. Run sysconfig, select the Server Fingerprint option and view the fingerprint

Answer: A


Q5. Which command would provide the most comprehensive diagnostic information to Check Point Technical Support?

A. fw cpinfo

B. cpinfo -o date.cpinfo.txt

C. diag

D. cpstat - date.cpstat.txt

Answer: B


Q6. Your expanding network currently includes ClusterXL running Multicast mode on two members, as shown in this topology:

Exhibit:

You need to add interfaces: 10.10.10.1/24 on Member A, and 10.10.10.2/24 on Member B. The virtual IP address for these interfaces is 10.10.10.3/24. Both cluster gateways have a Quad card with an available eth3 interface. What is the correct procedure to add these interfaces?

A. 1. Disable "Cluster membership" from one Gateway via cpconfig.2. Configure the new interface via sysconfig from the "non-member" Gateway.3. Re-enable "Cluster membership" on the Gateway.4. Perform the same steps on the other Gateway.5. Update the topology in the cluster object.6. Install the Security Policy.

B. 1. Configure the new interface on both members using WebUI.2. Update the new topology in the cluster

object from SmartDashboard.3. Define virtual IP in the Dashboard4. Install the Security Policy.

C. 1. Use WebUI to configure the new interfaces on both member.2. Update the topology in the cluster object.3. Reboot both gateways.4. Install the Security Policy.

D. 1. Use the command ifconfig to configure and enable the new interface on both members.2. Update the topology in the cluster object for the cluster and both members.3. Install the Security Policy.4. Reboot the gateway.

Answer: B


Q7. Your companyu2019s Security Policy forces users to authenticate to the Gateway explicitly, before they can use any services. The Gateway does not allow the Telnet service to itself from any location. How would you configure authentication on the Gateway? With a:

A. Client Authentication rule using the manual sign-on method, using HTTP on port 900

B. Client Authentication rule, using partially automatic sign on

C. Client Authentication for fully automatic sign on

D. Session Authentication rule

Answer: A


Q8. After filtering a fw monitor trace by port and IP, a packet is displayed three times; in the i, I, and o inspection points, but not in the O inspection point. Which is the likely source of the issue?

A. The packet has been sent out through a VPN tunnel unencrypted.

B. An IPSO ACL has blocked the packetu2019s outbound passage.

C. A SmartDefense module has blocked the packet.

D. It is due to NAT.

Answer: D


Q9. For best practices, what is the recommended time for automatic unlocking of locked admin accounts?

A. 20 minutes

B. 15 minutes

C. Admin account cannot be unlocked automatically

D. 30 minutes at least

Answer: D


Q10. When migrating the SmartEvent data base from one server to another, the first step is to back up the files on the original server. Which of the following commands should you run to back up the SmartEvent data base?

A. migrate export

B. eva_db_backup

C. snapshot

D. backup

Answer: B


Q11. To provide full connectivity upgrade status, use command cphaprob fcustat

Answer:


Q12. MegaCorps' disaster recovery plan is past due for an update to the backup and restore section to enjoy the benefits of the new distributed R80 installation. You must propose a plan that meets the following required and desired objectives:

Required: Security Policy repository must be backed up no less frequently than every 24 hours. Desired: Back up R80 components enforcing the Security Policies at least once a week. Desired: Back up R80 logs at least once a week.

You develop a disaster recovery plan proposing the following:

* Use the utility cron to run the command upgrade_export each night on the Security Management Servers.

* Configure the organization's routine backup software to back up files created by the command upgrade_export.

* Configure GAiA back up utility to back up Security Gateways every Saturday night.

* Use the utility cron to run the command upgrade_export each Saturday night on the log servers.

* Configure an automatic, nightly logswitch.

* Configure the organization's routine back up software to back up the switched logs every night. The corporate IT change review committee decides your plan:

A. meets the required objective and only one desired objective.

B. meets the required objective and both desired objectives.

C. meets the rquired objective but does not meet either deisred objective.

D. does not meet the required objective.

Answer: B


Q13. To bind a NIC to a single processor when using CoreXL on GAiA, you would use the command sim Answer:

affinity

Answer:


Recommend!! Get the High quality 156-915.80 dumps in VCE and PDF From Allfreedumps, Welcome to download: https://www.allfreedumps.com/156-915.80-dumps.html (New Q&As Version)